OBD2 Car Diagnostic Tool Share

CARDAQ-PLUS CARDAQ PLUS SAE J2534-1 J2534-2 Scanner

Launch iCarScan 5 brand free software iDiag DHL Free shipping

Problem: After replacing the EIS on this 2001 Mercedes W220 S500 the mileage now reads ----- on the dash. I’m guessing it’s because the das and EIS have different mileage values, ok that’s fine but where is the eeprom located in this dash? There is no ESL on W220, so I did not code in the new EIS. I virginised ECU and adapted used EIS. i dont see eeprom on other side either. i know how to read the EIS heres the dash 24c04 eeprom. https://mega.nz/#!1Ioi3DJD And here one experience locksmith have change my dump to 0 and my original mileage was 125024 https://mega.nz/#!lVB2WRYY Given Suggestion as follows: "You don't have mileage in this eis. May be the VIN of the car is in there, then you must try to 0 the dash, adapt with Star Diagnosis and after that change the mileage with STAR to what you need. When you zero the dash, the star will think that your dash is new and let you adapt with the car" Finally, solved with Star Diagnosis !! You need to chan...

Here is the instruction on Ford Focus 2.8L 2008 PCM reprogramming using Ford VCM II IDS diagnostic system clone. Main procedure: Step 1: Install a new PCM Step 2: Reprogram PCM Step 1: Install a new PCM Install VMware and well setup IDS software follow the video/pdf guide (see attachment below) Run Ford Module Programming Click on car icon Select “Start New Session” Press “Confirm” The SAE J2534 pass-thru device cables must not interfere the safe operation of the vehicle. Secure all cables away from the vehicle pedals. Make connection as shown Turn ignition to ON Apply the parking brake Apply Neutral/Park gear position Establishing communication to PCM Verify vehicle information Press programming icon Select “Module programming” Select “Programmable Module Installation”>> “PCM” Again verify vehicle information and confirm Turn ignition to OFF position (Position 0) Check if the displayed VIN is correct, if yes, hit Yes to continue Follow the ...

Launch iCarScan VCI Bluetooth Diagnostic Scanner is the perfect replacement of Launch iDiag auto diag scanner. Here is the instruction on how to register, activate and update/download iCarScan software. Launch iCarScan VCI Bluetooth Diagnostic Scanner User Manual http://www.obdexpress.co.uk/upload/pro/launch-icarscan-scanner-user-manual.pdf First of all, getting started with the iCarScan main function buttons: I． Download & Install the iCarScan App The iCarScan app is free to download. 1. Turn on your Android smart terminal.  2. Go into Android Play Store (Google play). Google play can be found in the following URL: https://play.google.com/store. 3. Input the keyword "ICARSCAN" in the search bar. 4. Once found, tap on "FREE" to download and install it. You are free to download 5 demo software. 5. After the installation is complete, an iCarScan icon will be created on the HOME screen. II. Register & activate Launch iCarScan software 1. C...

Mercedes-Benz MB SD Connect C4 is the only Star diagnostic system that is featured WIFI wireless connection via LAN cable . It is true that the WIFI only works with a D630 HDD & laptop? Questions before entering: I need help and have a question. Is it true that the WIFI only works with a D630? Because I use Xentry via VMWare and I search a solution to use SD Connect via WIFI. I have 2 Laptops. The one is a XPS M1710 and Xentry is installed internal HDD. The other Laptop is a Dell Studio and Xentry is installed via VMware external HDD. Can I use one of both methods the Wifi Connection? Answer: Regular Star diagnostic DAS/XENTRY has two formats Dell D630 HDD and external HDD. (IBMT30 is quite old software for Star C3 and it is now out of production.) Usually the Dell D630 HDD is installed on Dell laptop while external HDD is installed on VMware. External HDD on VMware cannot enable SD Connect WIFI wireless connection. Star diagnostic Platinum Edition HDD has 4 formats:...

This post starts with user’s real problem on Lexia PP2000 that no the interface is no longer recognized on USB port, then followed by the analysis on this problem and working solution, as well as Trouble shooting Description. Hope it helps! The problem: When connecting to the USB port, the card is recognized and detected with USB com board driver. After flash spi flash (Winbond W25Q80B) for changing the serial number and flash MB90F546GS microprocessor with SCARY file for recognition in EVOLUTION driver; the interface is no longer recognized on USB port ????? After re-reading the SPI flash, this one is empty ??? Finally, I found the problem on this interface (more precisely on the microprocessor MB90F546GS board). Solution: Missing +Vcc on the pull-up resistor 3.9 Kohms, inner track probably cut ... Setting up a wire to bring the +Vcc on the pull-up resistor. Trouble shooting Description: After changing many components, among other SPI flash, HA86, Micro MB90F546GS .....

Why this 368A key cutting machine is so cheap while Condor XC Master series cutting machine is so expensive? 368A and Xhorse Condor key cutter are totally different machines. 368A key cutter is the manual control version. You need to do Calibration and cutting keys manually. While Condor key cutting machine is the automatic version. It can do Calibration and cutting keys by itself automatically. Xhorse Condor XC MINI key cutting machine comes with build-in key database that will cut major vehicle key in the world. But the little 368A budget machine is great for cutting laser type keys. What key can 368A key cutting machine cut? 368a key cutter can cut/duplicate both home keys and vehicle keys (multi car brands, BMW, Honda, VW etc.) For detail what type of key can get cut, please check the user manual in the package or contact obdexpress.co.uk customer service. According to our customer’s feedback, 368A key cutting/duplicate machine is ideal for making duplicates or use ...

BMW ICOM Rheingold ISTA-D ISTA-P diagnostic & programming software is newly released to 2015.10V without USB dongle and can be worked on Win 8 operating system. Software version: ISTA-D:3.51.31 ISTA-P: 3.56.5.002 VIN: 2015.10.7 Top Feature: 1. Software compatible with ICOM, ICOM A2 and ICOM A3 2. Without USB dongle no need afraid for lost. 3.  Support Multi-language in diagnose and programming, also TIS diagram circuit:  Chinese, English and German Capacity: SS151-A10 SSD (Solid State Drive) 256GB SS151-10 HDD (Hard Drive) 500GB Software including & Functions System Requirements: Make sure your laptop has Dual-core processor, better above IE3, and the RAM should be 4G or above, to ensure the software run smoothly, if your laptop can not reach this configuration, the software will be not able to run. Support Model:  It is recommended to use Lenovo ThinkPad: T61, T410, T420, T430, X200, X201, X220 X230 and other laptop with Intel chipset, su...

Old BMW E38 and E46 have 20 PIN underhood connector rather than standard OBD II 16 Pin diagnostic socket. In contrast, the OBD II port allows you to keep the hood down, drive the car and sit in the driver or passenger seat to use your diagnostic tools ( BMW ICOM , INPA , BMW Scanner v1.4.0 etc). With the hood down you also keep the air intake flaps open for the climate control. Only problem is the ODBII only allows access to a limited number of control modules and if you're using DIS on a GT1 machine with a DK (yellow Diagnostic Head), the Auto ID will not work correctly as there is no switched power (Terminal 15) on the OBDII socket. You can either hook up a 20-pin to-16-pin diagnostic connector underhood or modified your diagnostic port to D-bus. Modification is certainly at risk. But I tried and it worked. You are on your own risk. BMW upgraded the OBDII diagnostic socket in 2001 to allow access to all control modules for all sales models except the E38 7-Series and t...