Original AUTEL MaxiSys Pro MS908P LCD Touch Screen
Original AUTEL MaxiSys Pro MS908P LCD Touch Screen
Posts
How to update Xprog 5.5.5 to 5.7.6 via Internet active
This is XPROG 5.5.5 to 5.7.6, software and firmware update internet active Unzip the zip file, run XProgDestop.exe 2. Press the Help -> Hardware Info and update the firmware 3. Do not press the Update Certificate Says it works 100%. But unluckily, i have no luck. I was thinking about upgrading my xprog box so I thought I would have little to lose by following instructions given to see what happens. Everything appears to go smoothly see pictures below. However, you cannot read or write any chips without being locked into a certificate error loop. see pics. Rolling back to 5.5.5 all authorisations are gone hardware registration ID is blank and unit wont read or write. So for the benefit, my advice is don’t use this I finally gave it up and spent some dollars with a new one (Xprog box 5.7.6, it’s from http://www.obdexpress.co.uk/wholesale/x-prog-box-ecu-programmer-x-prog-m.html ) It add...
2017.05 XDOS Xentry 2221-45 & 3.91 Fix Download Free
Free download 2221-45 & 3.91 Fix for Xentry/DAS 2017.05 https://mega.nz/#!5GxEyCZa!9w8E4btOqovhaA2X_IXmKdecp64WnhEDio6m3-V-yeE Again, this is for 2017.05 Xentry.OpenShell.XDOS only. Try on your own risk. OBDexpress.co.uk hold no responsibility of what you will try. The issue & solution you may need: (StarInsecure) ID is automatically lost The most idiotic way how to make a full shit from the system! FIRST! You must understand how it works totally before to kill it with your stupid replacing. 1. com.daimler.xentry.diagservice_1.7.0.201703101035.jar = encoded with another algorithm from 2017.05. The system CAN`T READ this file with an old encoding, YOU COULD SIMPLY TO DELETE THIS FILE in case of it. The hell of instructions are lost. 2. com.daimler.fusoko.variables_1.22.9.201703101035.jar = not encoded, but from 2016.09 version I don`t see any work here. Try to decode their “ old ” o...
CarProg Manual: Carprog clone read Motorola MC68HC05
Carprog manual ... Here you go... about how to read Motorola MC68HC05 using a CarProg programmer? What basic info you need to know? You need recognize Motorola (Freescale) MPU by maskset; This MPU maskset is 3D33J; Before programming, always select right processor type according maskset. Which version of Carprog do you need? First, Carprog full original or Carprog clone? It depends on your budget. But Carprog programmers china clone now can work without issues with Motorola MC68HC05, especially in Carprog airbag . You have optional solutions: Carprog v8.21 : it’s the perfect online version and Caprog 9.31 : the newest china version How to connect to a CarProg programmer? For HC05 programming use A10 cable 7 color wires: YELOW – communication signal from MPU; GREEN – communication signal to MPU; BLUE – Reset signal to MPU; ORANGE – MODB signal to MPU, low level; BROWN – GND (ground); RED – switched +5V; VIOLET - switched +12V; ...
which tool should you use for PSG16 ECU programming?
How to reset/program Zafira PSG16: with Carprog? Opcom? Tech2+GlobalTIS? Here is the how-to guide for you; a good discussion of Zafira PSG16 replacement and programming here. Is it possible to install PSG16 ECU from vectra C to zafira and oppositely from zafira to vectra ? Yes, it is possible to install from zafira to vectra and oppositely D id you tr y to reset with O pcom? Yes I tried opcom but when I put 0608 it gives me security wait time. Carprog says FFFF. W hy C arprog can ’ t do reset ? If the pump has come from a Vectra C and your fitting it on a Zafira A then it wont reset; the best way is to do a SPS update with Tech 2 and GlobalTis to overwrite the software in the pump then program it with the cars own security code Vectra C use CAN communication, and Zafira use K-Line communication protocol. Without SPS or another device for re flashing, not possible change. W hat if I put it in Vectra C, it will be ...
DAS Internal error: (3.91)-3.11 (customer solution)
Today I connect to car W211 ( DAS ) with 12.2016, I get this Error. System error Internal error: (3.91)-3.11 You must contact the user help desk. I resolve Megacar 3.91 issue. I get 20+ PM for help everyday and I helped them all. Thanks bud for showing a good attitude to 12_2016. I do not understand why some releasing a fix with conditional $$. Little bit of ingenuity, 12_2016 works flawless. I am the first one put 2 torrent for 12_2016 and one 09_2016. I probably fixed 50+ 3.91 error in this forum and other various forum for free. Like a superstar said, you gotta understand the system. I am a car fanatic. Having a e55, R350, Brabus 7.3s (30 made), Alpina B10- biturbo (317 made), Lotus Esprit twin turbo (97 car per year). Porsche Cayenne Turbo S (735hp), Two Ferrari 360 modena 445 hp), Mini, M3, M5, 330ix, Acura TSX 6spd tuned wit nitro and twin turbo to 400+, JAG XJS, Range Rover and a FOOOken Prius. I had all CN Sw for all my car and one day got decided to do own m...